Skip to main content

How to fix your broken laptop screen

How to fix your broken laptop screen



Before starting, ensure you have the proper tools. Here’s what works for most laptops:
•Table or other flat working area: You’ll need a spot to sit (or stand, if that’s your thing) with a flat area to work on your laptop.
•Small-head magnetic Philips screwdriver: If you don’t have a magnetic-head screwdriver, try to find a magnet big enough to magnetize the driver head. This helps the screws stick to the head, making it much easier to remove and replace the screws without cursing as they fall all over the place.
•Plastic putty knife or other thin object: This is optional, to aid in prying apart the screen bezel from the case. Personally, my finger nails usually do the trick. If you do use another object, ensure its thin enough but not so sharp that it will leave scrapes or other evidence of prying.
•Safety pin or needle: This is for removing the cover stickers that are hiding the screws on your laptop’s surrounding cover, called the bezel.
•Small bowl or other container: This is for stashing the small screws—and keeping them safe from curious cats and children.
These general steps work for most laptops:
1. Ensure the laptop is unplugged from the AC adapter. Remove the laptop battery as well.
2. Find the round cover stickers that are hiding the screws on the screen bezel, the case surrounding the screen. These stickers are usually on the bottom of the bezel, near the screen hinges, when you have the screen opened. You should find one on each side of the screen.
Use a sharp, pointy object—like an opened safety pin or needle—to help remove the cover stickers without damaging them. Stick it between the edge of the cover and bezel, and then pry the sticker away. Once removed, place the covers in a safe spot, with the sticky side up to help ensure there’s enough stickiness when you place them back on.
3. Use your screwdriver to remove the now-exposed screws. Carefully start prying the screen bezel away from the back side of the screen case. Work a fingernail or other thin, prying object into the crack around the outside of the screen. The bezel is usually secured to the back case with plastic snaps, so give it some force while prying—but not too brutish. You’ll hear the unsnapping of the fasteners when prying.
Once the bezel is fully removed, you’ll find the LCD secured to a metal trim frame on the left and right sides. Remove the two screws (one on each side, on the top) holding the trim frame pieces to the back-screen case. Now, you should be able to lift the LCD (with the trim frame pieces attached) slightly away from the back-screen case.
4. On each of the trim frames’ sides, remove any screws that are securing it to the LCD..
Now you should be able to set the LCD face-down onto the keyboard. Be careful not to put excessive force on the video cable attached to the back of the LCD. Disconnect the video cable from the back of the LCD. If so, keep in mind that the portion of the cable running down the screen is usually stuck on the back of the screen with some mild adhesive. Just gently pull the cables away from the screen. You usually must remove tape that’s securing the video connector to the back of the screen as well. When you get to the point of pulling the video cable out of the screen connector, it should unplug with little force.
Once you've fully removed the broken LCD, simply place the new one face-down like you did the old one. Reattach the video cable to the connector and place the cables and any tape just like they were for the old one.
5. Set the new screen up in the side trim frame pieces, then re-secure it like the old one was: usually three screws in each side of the trim frame pieces, and then a screw on top of each to secure it to the back-screen case.
6. When you get to the point of putting the bezel back on, just line it up and push/squeeze the bezel back into the snaps of the rear screen case. Before replacing the bezel screws, ensure the bezel is fully snapped in place and no crack exists around the edges of the screen case. Lastly, use that safely pin or needle to reattach the sticky screw covers.
If all went well, you now should have a shiny new working laptop screen. Put the battery back in and test it out!

Comments

Popular posts from this blog

मंगल ग्रह पर सबसे पहले जाने वाला व्यक्ति कौन है और किस ने महल बनाया?

मंगल ग्रह पर सबसे पहले जाने वाला व्यक्ति कौन है और किस ने महल बनाया ? मंगल ग्रह पर सबसे पहले जाने वाला व्यक्ति है भरत सामजी(Bharat Samgi)। भरत सामजी(Bharat Samgi) मूल निवासी मलाला दिव भारत के है और हाल में लंदन में रहते है। मंगल ग्रह पर भरत सामजी ने १ लाख एकड़ का एक प्लॉट ख़रीदा। भरत सामजी ने प्रकाश की गति जितना उड़ने वाला एक रॉकेट बनाया। वो उस रॉकेट में सारा सामान भर कर पृथ्वी से मंगल ग्रह की तरफ उड़ान भरने लगा। मंगल ग्रह पर उतर कर उसने अपने परिवार के साथ मिलकर एक बड़ा सा महल बनाया। आधुनिक सुविधा के साथ वहाँ रहने लगे। खूब आनंद मस्ती के साथ वहाँ रहते थे। खाने पिने की बहुत सुविधा थी। उसने अपना सारा सिस्टम बनाया था। एक दिन वो रात को सो रहे थे तब अचानक बेल बजने की आवाज आई। आंख खोलकर देखा तो पृथ्वी पर अपने घर में बिस्तर पर था और दरवाजे पर कोई बेल बजा रहा था। तब पता चला की मंगल ग्रह पर ज़मीन लेना और महल बनाना एक स्वप्न था। स्वप्न कभी भी किसी को आ सकता है।  स्वप्न पर किसी का नियंत्रण होता नहीं है। और स्वप्न देखने का पैसा भी लगता नहीं है।

Online appointment booking for Portuguese passport and BI renewal

Online appointment booking for Portuguese passport and BI renewal

दीव प्रशासन आईएनएस खुकरी को औपचारिक रूप से 26 जनवरी को प्राप्त करेगा

दीव प्रशासन आईएनएस खुकरी को औपचारिक रूप से 26 जनवरी को प्राप्त करेगा। आईएनएस खुकरी को देश की 32 साल की सेवा के बाद सेवामुक्त किया गया। पहला स्वदेश निर्मित मिसाइल कार्वेट, आईएनएस खुकरी, जिसे पिछले साल दिसंबर में 32 साल की सेवा के बाद सेवा से हटा दिया गया था, सोमवार को दीव पहुंचा। दीव कलेक्टर सलोनी राय ने कहा, 'दीव प्रशासन इसे औपचारिक रूप से 26 जनवरी को प्राप्त करेगा और जनता के देखने के लिए उपलब्ध होगा। कार्वेट 1989 में मझगांव डॉक शिपबिल्डर्स द्वारा बनाया गया था और इसे पश्चिमी और पूर्वी दोनों बेड़े का हिस्सा होने का गौरव प्राप्त था।    आईएनएस खुकरी भारतीय नौसेना का टाइप 14 युद्धपोत था। वह 1971 के भारत-पाकिस्तान युद्ध के दौरान 9 दिसंबर 1971 को पाकिस्तानी नौसेना डैफने-श्रेणी की पनडुब्बी हैंगर द्वारा दीव, गुजरात, भारत के तट पर डूब गई थी। द्वितीय विश्व युद्ध के बाद पनडुब्बी द्वारा कार्रवाई में यह पहला युद्धपोत था। लंबाई: 300 फीट (91 मीटर) पीपी 310 फीट (94 मीटर) ओआ लॉन्च किया गया: 20 नवंबर 1956 कमीशन: 16 जुलाई 1958 गति: 27.8 समुद्री मील (51 किमी/घंटा) अधिकतम, 24.5 समुद्री मील (45 किमी/